Puget 3D

Shop / SNE-1 Chassis Plate for RAK WisBlock

SNE-1 Chassis Plate for RAK WisBlock

Plate only. No electronics are included: no RAK or other LoRa boards, charger, power monitor, batteries, battery holder or enclosure. You get the printed plate with its screws, straps and zip ties.

A drop-in electronics plate that turns an SNE-1 enclosure into a solar LoRa repeater (MeshCore or Meshtastic). Standoffs for a RAKwireless RAK19007 WisBlock base, an Adafruit bq24074 solar charger and an Adafruit INA3221 power monitor, plus a cradle for a Geekworm X12-A1 V1.0 4 × 18650 battery holder. Every board screws straight into self-threading pilots, so there are no inserts or nuts to fit.

PETG · Fits any SNE-1 v2 box · Ships in 3 business days · SNE1-CP-MC v1.5

$10

Electronics
Not included (no boards, batteries or holder)
Size
163 × 97 mm, 3.5 mm plate, 10.8 mm overall
Material
PETG
Fits
Any SNE-1 v2 box (interface I1: 4 × M3 on 148 × 78 mm)
Boards
RAK19007 + RAK4631, bq24074, INA3221, Geekworm X12-A1 V1.0
Board fixing
Ø2.2 mm self-threading pilots for M2.5, no inserts or nuts
Box fixing
4 × M3 × 10 countersunk, heads flush
In the pack
Plate, 18 stainless screws, 2 straps, 6 zip ties

Overview

Buy it to build a MeshCore or Meshtastic node in an SNE-1 box you already have, as a spare plate for a second build, or to swap a box from the generic grid plate to a ready-laid-out RAK build. It's the same plate that comes with the SNE-1 kit when you choose the MeshCore plate. Four countersunk M3 screws hold it in the box.

  • Laid out for a complete solar node

    RAK19007 (USB-C toward the top), bq24074, INA3221 and a 4 × 18650 holder, with the wiring runs kept short.

  • No inserts or nuts

    Ø2.2 mm self-threading pilots take ordinary M2.5 machine screws, which cut their own thread on the first turn. The M2.5 × 5 screws that come with the X12-A1 also fit its four standoffs.

  • Battery cradle

    Rails that clear the holder's solder pins, 4 M2.5 standoffs on the X12-A1's own holes and 4 slots for hook-and-loop straps. Use screws, straps or both.

  • Cable routing

    A panel-lead slot from the PG7 gland behind the plate, a return hole by the charger, and 4 zip-tie slot pairs.

  • Debossed labels

    Each board's position, the battery output side, the USB-C direction and the panel lead are marked on the plate.

  • Clears the box hardware

    Notches clear the N-bulkhead nuts at both antenna positions.

Board positions

Position (from the front)Board (not included)Fixing
Left two-thirdsGeekworm X12-A1 V1.0 4 × 18650 holder (93.9 × 77.1 mm; holes 86.9 × 57.77 mm, measured on the shipped board)4 × M2.5 on 3.5 mm standoffs and/or 2 hook-and-loop straps
RightRAKwireless RAK19007 WisBlock base with RAK4631 core (30 × 60 mm), USB-C up4 × M2.5 on 5 mm standoffs
Centre bottomAdafruit bq24074 USB/DC/solar LiPo charger (33 × 38 mm)4 × M2.5 on 5 mm standoffs
Centre topAdafruit INA3221 3-channel power monitor (23 × 38 mm)2 × M2.5 on 5 mm standoffs

Specifications

Size163 × 97 mm (6.42 × 3.82 in); right section 88 mm tall
Thickness3.5 mm plate; 10.8 mm overall with the cradle walls
MaterialPETG
Board standoffsØ6 mm, 5 mm tall (battery 3.5 mm), Ø2.2 mm self-threading pilots for M2.5
Box fixing4 × M3 countersunk (90°) on 148 × 78 mm, heads flush
Clearance to the closed SNE-1 lidRAK19007 + RAK4631 17.9 mm · bq24074 25.4 mm · INA3221 21.9 mm · 18650 cells 11.9 mm
Cable routingPanel-lead slot 12 × 5 mm, return hole 7 × 6 mm, 4 zip-tie slot pairs (2 × 4 mm), 4 strap slots (14 × 2.8 mm)
Weight≈ 55 g (estimate)
BrandingPuget3D logo and puget3d.com in texture contrast (same filament)

Clearances use typical board heights. Taller WisBlock module stacks or added headers reduce them.

Dimensions and drawings

True-scale drawings from the CAD model, in mm. Select a drawing to open it full size. The 18 hole positions are also available as a CSV table.

Dimensions drawing: plate outline 163 by 97 mm, the I1 screw pattern, notches and slots
Outline, I1 screw pattern, notches and slots.
Mounting holes drawing: board footprints and all 18 labelled hole positions
Board footprints and all 18 hole positions.
Heights drawing: board heights in the box and clearance to the closed lid
Heights in the box and clearance to the lid.
Board layout drawing: board positions on the plate and the power wiring between them
Board positions and power wiring.

In the pack

QtyItem
1Chassis plate SNE1-CP-MC v1.5 (PETG)
4M3 × 10 countersunk screws, A2 stainless (don't use longer: they bottom out in the box inserts)
14M2.5 × 8 pan-head screws, A2 stainless (RAK ×4, bq24074 ×4, INA3221 ×2, X12-A1 ×4)
212 mm hook-and-loop straps, ~300 mm
6Small zip ties (≤ 3.6 mm)

Not included: the SNE-1 box, boards, 18650 cells, wiring, antennas and the solar panel.

Fitting

  1. On the bench, screw the RAK19007, bq24074 and INA3221 to their standoffs.
  2. Wire the boards. Route the panel lead from the PG7 gland behind the plate (bottom-right slot) and out through the centre-right hole.
  3. Fix the plate into the box with the 4 × M3 × 10 countersunk screws. Snug only.
  4. Drop the battery holder into the cradle with its outputs toward the boards, then screw it down and/or strap it.

The battery holder covers the two left plate screws: fit the plate before the battery, and take the battery out first when you remove the plate.

Self-threading pilots: drive each M2.5 screw slowly, by hand. The first turn forms the thread; a fast driver melts PETG. Stop at snug. Treat each hole as one-time: a screw can go back into its own thread a few times, but it will loosen eventually. If a screw is very tight, run a Ø2.3 mm drill through by hand first.

Battery safety

  • Use four matched, protected or button-top 18650 cells from a reputable supplier, and check the X12-A1's polarity marks before inserting them. The cells sit in parallel, so charge them to the same voltage before you fit them.
  • The X12-A1 V1.0 has a resettable fuse per cell but no BMS: it doesn't stop over-discharge or over-charge. Pair it with a 1S protection board (BMS) on the pack output and a charger with a temperature cut-off, as in the MeshCore build.
  • Lithium cells must not be charged below 0 °C. Before an outdoor winter install, check that your charger's thermistor (TS) input is set up to stop charging in the cold.
  • Keep bare cell ends and the holder's pins clear of the box screws and wiring.

Compatibility

  • SNE-1: fits any SNE-1 v2 box (chassis interface I1: 4 × M3 brass inserts on a 148 × 78 mm pattern, boss tops 6 mm above the back wall).
  • Other enclosures: anything with 4 × M3 on 148 × 78 mm, at least 163 × 97 mm of floor and about 40 mm of depth. The plate needs nothing from the SNE-1 apart from the screw pattern.
  • Plate versions: v1.5 moves the two lower battery standoffs up 3.73 mm to suit the X12-A1 V1.0 as Geekworm ships it (hole spacing 86.9 × 57.77 mm, measured). Nothing else changed from v1.4.
  • RAKwireless, WisBlock, Adafruit and Geekworm are named only to describe compatibility. Puget 3D isn't affiliated with or endorsed by them.

Shipping

Shipped within the US by USPS, or local pickup on the Eastside. Rates are shown at checkout.

Returns

Problems with an order? Contact us and we'll make it right. Return policy.

Custom changes

Want a different size, color or material? Ask for a quote instead.